Jump to the main content

Search Budget Builds Daily

DIY vs Pro Savings Calculator: Is It Cheaper to Do It Yourself?

Author: Published on

DIY saves money when the pro quote is higher than your cash costs (materials, tools you must buy or rent, permits and the materials you waste to mistakes) plus the value you put on your own hours. This calculator adds those up and solves for your break-even hourly value, the rate at which doing it yourself and hiring out cost the same. Every price is your own input.

DIY vs pro calculator

Enter your costs and a written pro quote. The amounts below are a hypothetical example, so replace each one. Results update as you type, are saved in the page address and never leave your browser.

Your job

Used only for the wage reference below the result.

Example amount: replace with your own.

What you expect to recoup, or the value of reuse. Capped at the purchase price.

Include shopping, setup and cleanup.

Your choice. Use 0 if you value the time at nothing.

Our planning default, not a published figure.

Get it in writing.

Optional, for the wage reference.

DIY vs pro

How the calculator works

It adds your cash costs and a mistake allowance, values your hours, and compares the total with the pro quote. It also solves for the hourly value at which the two options cost the same, so you can judge the result against your own time.

DIY versus pro
mistakes   = materials × mistake % ÷ 100
DIY cash   = materials + (tools bought − resale) + rental + permits + mistakes
DIY total  = DIY cash + hours × hourly value
savings    = pro quote − DIY total      (cash savings uses DIY cash)
break-even = (pro quote − DIY cash) ÷ hours
hourly value
what one hour of your time is worth to you
break-even
the hourly value at which DIY total equals the quote

Worked example (hypothetical job)

Given: materials $300; tools to buy $100, no resale; rental $50; permits $0; 12 hours of your time at $20 an hour; 10% mistake allowance; pro quote $900.

  1. Mistake allowance: 300 × 10 ÷ 100 = $30
  2. DIY cash: 300 + 100 + 50 + 0 + 30 = $480
  3. Value of your time: 12 × 20 = $240
  4. DIY total: 480 + 240 = $720
  5. Savings after time: 900 − 720 = $180 (cash savings: 900 − 480 = $420)
  6. Break-even hourly value: (900 − 480) ÷ 12 = $35 an hour

Answer: DIY saves $180 after valuing your time. It stays cheaper as long as an hour of your time is worth less than $35. The amounts are an illustration, not typical prices.

Wage reference by trade

U.S. median hourly wage by trade, 2025 (employee wages, not contractor prices)
TradeMedian hourly wageSource
Drywall installers and tapers $28.74Source 1
Painters $23.75Source 1
Carpenters $29.12Source 1
Electricians $30.38Source 1
Plumbers, pipefitters and steamfitters $30.67Source 1

BLS Occupational Outlook Handbook, 2025 median pay. A quote includes overhead, insurance, profit and materials handling, so expect it to exceed pro hours times these wages.

Assumptions and limits

  • Every price is your input. The starting amounts are a hypothetical example, not typical costs, and the calculator publishes no price of its own.
  • The mistake allowance is our planning default. There is no published rate, so set it to match your experience.
  • The pro quote is assumed to be all-in. Compare quotes that include the same scope: demolition, cleanup, permits and warranty.
  • The wage reference is context, not a price. BLS wages exclude a contractor's overhead, insurance and profit.
  • Money is not the only factor. Safety, code compliance, insurance and the quality of the finished work can matter more. ESFI strongly recommends a licensed electrician for any electrical work, and gas, structural and permitted work belongs with a professional too.
  • This is a planning tool, not financial or construction advice.

Questions and answers

Is DIY always cheaper than hiring a pro?

No. DIY is usually cheaper in cash, because you skip the contractor's labor, overhead and profit, but it is not always cheaper once you count tools you have to buy, materials wasted on mistakes and your own hours. The calculator shows both numbers: the cash saving, and the saving after your time is valued, so you can see which jobs pay and which do not.

How do I price my own time?

Pick a rate you would honestly accept for the hours: what you would earn from extra work, or what you would pay someone else to take the job off your hands. Zero is a legitimate choice if you enjoy the work and have the time. The break-even figure removes the guesswork: if your hour is worth more than that number, hire the pro.

What is the break-even hourly value?

It is the pro quote minus your DIY cash costs, divided by the hours you expect to work. Below that value of your time, doing it yourself costs less in total; above it, hiring costs less. It turns a vague question into one number you can judge against your own wages or free time.

Why include a mistake allowance?

First-time DIYers cut wrong, buy the wrong size and redo steps. The calculator applies a percentage of your materials budget as spare cost. There is no published industry figure, so the starting value is only a planning default of our own; raise it for skills you have never used and lower it for work you repeat often.

What should I never do myself?

Electrical work is the clearest case: the Electrical Safety Foundation International strongly recommends hiring a qualified, licensed electrician for any electrical work in your home. For any other work that your area says needs a licensed trade or a permit, follow those rules. Your local building department can tell you which jobs they cover before you start.

Does the calculator know what a pro charges?

No, and it does not guess. Prices vary by region and season, so you type in a written quote. For context only, the tool shows the median hourly wage the U.S. Bureau of Labor Statistics reports for the trade. That is a wage paid to an employee, not a billed rate, so a real quote also carries overhead and profit.

Do I need a permit for DIY work?

It depends on your city or county and on the work. Permits are issued by the local building department, and each one sets its own list of jobs that need one, so ask before you start. Enter any permit fee in the permits line so it is counted, and call the building department before you start.

Our sources

  1. U.S. Bureau of Labor Statistics, Occupational Outlook Handbook: construction and extraction occupations, 2025 median pay (bls.gov) Accessed 2026-11-14. Each trade has its own page; links are in the table below.
  2. Electrical Safety Foundation International, DIY Electrical Safety (esfi.org) Accessed 2026-11-14.

Related reading